{"id":7399,"date":"2020-09-06T17:34:56","date_gmt":"2020-09-06T15:34:56","guid":{"rendered":"https:\/\/advancedfleetmanagementconsulting.com\/eng\/?p=7399"},"modified":"2020-09-06T17:34:56","modified_gmt":"2020-09-06T15:34:56","slug":"maintenance-recommendations","status":"publish","type":"post","link":"https:\/\/advancedfleetmanagementconsulting.com\/eng\/2020\/09\/06\/maintenance-recommendations\/","title":{"rendered":"Kingpin Inspection and Maintenance Recommendations"},"content":{"rendered":"

Kingpin inspections\/maintenance should be conducted every three months or 30,000 miles. Photo: SAF-Holland<\/em><\/span><\/p>\n

Trailer upper coupler or bolster plate and kingpin inspection and maintenance is just as important as the inspection and maintenance of the fifth wheel. The following procedures are based upon recommendations outlined in SAE J2228.<\/span><\/p>\n

To assure proper and safe kingpin\/fifth wheel coupling, kingpin inspection and maintenance should be conducted every three months or 30,000 miles.<\/span><\/p>\n

1. Using a 48-inch straight edge or a large metal right angle square, check the upper coupler plate flatness in all directions as shown in Figure 1. Any bumps, valleys, or warping will cause uneven loading of the fifth wheel, which could result in damage to the top plate and reduce lock life. If flatness exceeds the specifications as shown in Figure 2, replace the trailer upper coupler plate.<\/span><\/p>\n

\"Figure<\/span>
\n

Figure 1 <\/span>Photo: SAF-Holland<\/em><\/span><\/p>\n<\/figcaption><\/figure>\n

2. Using a square or Holland Kingpin Gage (TF-0110), check to see if the kingpin is bent. A bent kingpin can result from excessive coupling speed or impacting the trailer into a dock. A bent kingpin accelerates lock wear and may interfere with proper fifth wheel locking. This also may indicate damage. If the kingpin exceeds 1\u00b0 from square in any direction as shown in Figure 2, replace it.<\/span><\/p>\n

In addition to being bent, the kingpin may be pulled down in the center, deforming the bolster plate as shown in Figure 2. If this condition exists, replace the kingpin.<\/span><\/p>\n

\"Figure<\/span><\/p>\n

Figure 2 <\/span>Source: SAF-Holland<\/em><\/span><\/p>\n

\n

3. The kingpin must be the proper length to couple properly with a fifth wheel. Using a Holland Kingpin Gage, check the length of the kingpin for proper length as shown in Figure 3. A long kingpin will result in excessive wear in the locks and coupling difficulty. A short kingpin will accelerate lock wear and may interfere with fifth wheel coupling. If either condition exists, replace the kingpin.<\/span><\/p>\n

\"Figure<\/span>
\n

Figure 3 <\/span>Photo: SAF-Holland<\/em><\/span><\/p>\n<\/figcaption><\/figure>\n

If an add-on aftermarket lube plate is used in your operation, make sure to check the kingpin length. The kingpin must be sized to compensate for the thickness of the lube plate. Otherwise, the kingpin will be too short. If the kingpin length is improper, the kingpin should be replaced.<\/span><\/p>\n

4. Check the kingpin for wear as shown in Figure 4. If the kingpin is worn 1\/8 inch (.125 inch) or more on either the 2-inch or 2-7\/8-inch (2.875 inch) diameter in either direction, replace the kingpin. If using a Holland Kingpin Gage, wear is indicated if the appropriate diameter enters the gage slot. If the gage slides into the gage slot, replace the kingpin.<\/span><\/p>\n

\"Figure<\/span>
\n

Figure 4 <\/span>Photo: SAF-Holland<\/em><\/span><\/p>\n<\/figcaption><\/figure>\n

5. Inspect the kingpin mounting for a secure connection to the upper coupler. A loose kingpin mounting will cause excessive chucking and rapid lock wear. Reinstall or replace any kingpin that is not securely mounted.<\/span><\/p>\n

6. Inspect the kingpin for any nicks, gouges, deformation, or cracks, which may interfere or affect the safe use of the kingpin. If any damage is present, replace the kingpin.<\/span><\/p>\n

7. Kingpins are made from quenched and tempered alloy steel. Weld repairs of any type will affect the strength and wear resistance of the kingpin. Additionally, arc strikes or weld craters could develop a stress riser, leading to a fatigue failure. For these reasons, SAF-Holland warns against any weld repairs. If any deficiencies are noted during kingpin inspection, replace the kingpin (see Figure 5).<\/span><\/p>\n

\"Figure<\/span>
\n

Figure 5 <\/span>Source: SAF-Holland<\/em><\/span><\/p>\n<\/figcaption><\/figure>\n

8. If kingpin replacement is required, a replacement kingpin should be selected which is similar to the type removed, or if a different style, one which can be adequately braced. The kingpin must also be matched to the thickness of the upper coupler to maintain the SAE dimensions. Kingpins are manufactured in different lengths to match the thickness of the upper coupler. Improper selection will result in a kingpin that is too long or too short as indicated in Figure 6.<\/span><\/p>\n

\"Figure<\/span>
\n

Figure 6 <\/span>Source: SAF-Holland<\/em><\/span><\/p>\n<\/figcaption><\/figure>\n

NOTE: The above steps are recommended by SAF-Holland for proper inspection and maintenance of kingpins. Follow your specific kingpin manufacturer\u2019s instructions for maintenance and replacement procedures.<\/em><\/span><\/p>\n

This article was authored and edited according to HDT editorial standards and style to provide useful information to our readers.<\/em><\/span><\/p>\n

 <\/p>\n

by Rob Nissen, director of field service, SAF-Holland<\/p>\n

Source: https:\/\/www.truckinginfo.com<\/a>
\n<\/span><\/p>\n

CUT COTS OF THE FLEET WITH OUR AUDIT PROGRAM<\/strong><\/a><\/h3>\n

\"\"<\/a><\/p>\n

The audit is a key tool to know the overall status and provide the analysis, the assessment, the advice, the suggestions and the actions to take in order to cut costs and increase the efficiency and efficacy of the fleet. We propose the following fleet management audit.<\/p>\n

FLEET MANAGEMENT AUDIT<\/strong><\/a><\/h3>\n","protected":false},"excerpt":{"rendered":"

Kingpin inspections\/maintenance should be conducted every three months or 30,000 miles. Photo: SAF-Holland Trailer upper coupler or bolster plate and kingpin inspection and maintenance is just as important as the inspection and maintenance of the fifth wheel. The following procedures are based upon recommendations outlined in SAE J2228. To assure proper and safe kingpin\/fifth wheel…<\/p>\n","protected":false},"author":3,"featured_media":7401,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[18],"tags":[53],"_links":{"self":[{"href":"https:\/\/advancedfleetmanagementconsulting.com\/eng\/wp-json\/wp\/v2\/posts\/7399"}],"collection":[{"href":"https:\/\/advancedfleetmanagementconsulting.com\/eng\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/advancedfleetmanagementconsulting.com\/eng\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/advancedfleetmanagementconsulting.com\/eng\/wp-json\/wp\/v2\/users\/3"}],"replies":[{"embeddable":true,"href":"https:\/\/advancedfleetmanagementconsulting.com\/eng\/wp-json\/wp\/v2\/comments?post=7399"}],"version-history":[{"count":1,"href":"https:\/\/advancedfleetmanagementconsulting.com\/eng\/wp-json\/wp\/v2\/posts\/7399\/revisions"}],"predecessor-version":[{"id":7402,"href":"https:\/\/advancedfleetmanagementconsulting.com\/eng\/wp-json\/wp\/v2\/posts\/7399\/revisions\/7402"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/advancedfleetmanagementconsulting.com\/eng\/wp-json\/wp\/v2\/media\/7401"}],"wp:attachment":[{"href":"https:\/\/advancedfleetmanagementconsulting.com\/eng\/wp-json\/wp\/v2\/media?parent=7399"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/advancedfleetmanagementconsulting.com\/eng\/wp-json\/wp\/v2\/categories?post=7399"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/advancedfleetmanagementconsulting.com\/eng\/wp-json\/wp\/v2\/tags?post=7399"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}